|Built-In:||Power failure, Sound Level, One temperature sensor included|
|Inputs:||4-contact or temperature|
|Notifications:||4 custom voice phone calls|
|Built-in CottageSitter Thermostat control|
|Sensaphone 400 w/ International Power Supply|
|Sensaphone 400 Functional Diagram|
(click for larger image)
(new replacement for the 1104 and a direct replacement for the CottageSitter)For small businesses, property owners, and more, the ALL NEW Sensaphone 400 offers an easy, inexpensive way to monitor a remote facility. It can be installed in any clean indoor environment to monitor a variety of applications.
Dual Setback Thermostat for 400/800
Product # FGD-0064
For use exclusively with the Sensaphone 400 and 800, this is a "setback" thermostat with an LCD readout. It lets you enter the desired setpoint for both your "away" and "home" temperatures. A control signal, sent from your Sensaphone, switches between these two settings.
12V Power Supply for Thermostat
Product # XFR-0024
Required to supply power to the FGD-0064 Remote setback thermostat.
Product # FGD-0010
50ft. of 22-gauge shielded wire for connecting sensors to your sensaphone.
Mini Surge Protector - Power and Phone
Product # FGD-0067
The Traveler surge suppressor offers complete AC and phone line surge suppression for your Sensaphone and other electronic devices. The compact housing weighs less than 4 ounces. The retractable plug prevents scratching of expensive portable electronics. A set of RJ11 telephone line suppression jacks protect dialup and voice/modem lines. The suppressor offers 2 total outlets in a space saving direct plug-in format and diagnostic LEDs to warn of wiring problems and suppressor damage. $50,000 Ultimate Lifetime Insurance (USA & Canada Only).
Bluetooth Cell Phone Interface
Product # FGD-0230
The XLink allows your Sensaphone to dial and receive calls using any cell phone with Bluetooth technology. For example, suppose land-line telephone service was unavailable at the Sensaphone's location. By using the XLink you can provide telephone service to your Sensaphone by locating a cell phone next to the device. The XLink will send all incoming calls to the Sensaphone and when the Sensaphone needs to dial out the call will be seamlessly completed through the cell phone. The XLink is a wireless (Bluetooth) link between your Sensaphone and a cellular phone. This can be a cost-effective option considering that many cellular providers offer inexpensive options to add another phone. Perfect for access where a land line simply isn't available, the XLink is a must.
Magnetic Reed Switch
Product # FGD-0006
The magnetic reed switch may be used with all Sensaphone models to detect any unauthorized entry or intrusion. They are usually installed on doors and windows to detect their opening and closing. Several magnetic reed switches may be wired in series.
Infra-Red Motion Detector
Product # FGD-0007
The passive infra-red motion detector can be used with all Sensaphone models to monitor the movement of warm bodies in a specific area. It will cause an alarm if motion is detected. Its range of detection covers approximately forty feet of area. Multiple sensors can be wired in series to a single output.
Spot Water Detector
Product # FGD-0013
The water detection sensor can be used with all Sensaphone models to detect the presence of water on a horizontal surface. Independently powered by internal lithium batteries. The batteries should last for approximately 3-5 years. When the batteries start to run down, the sensor will automatically cause an alarm dial out when no water is present. Multiple sensors can be wired in series to a single input.
Product # FGD-0022
The Temp Alert can be used with all Sensaphone models to monitor air temperature from -30° to 130°F (-34° to 54°C). Simply determine the acceptable temperature limits for your application by adjusting the temperature limit arms. When the temperature exceeds the setting, the sensor triggers an alarm. The temp alert can be mounted to any wall or vertical surface. Multiple temp alerts may be wired in parallel to a single input. It requires no power for operation and mounts easily on any flat surface.
Product # FGD-0027
The Humidistat can be used with all Sensaphone models to detect a high or low humidity level. The device will cause your Sensaphone to activate an alarm when the humidity level reaches a set threshold. Made from high impact plastic with a brushed goldtone dial plate and a beige cover. A nylon sensing element provides long life and accurate humidity control. With a range of 10% to 60% RH level, the sensor causes an alarm when the humidity exceeds or falls below the set limit. Multiple sensors may be wired to a single input.
Smoke Detector 110VAC
Product # FGD-0049
The Smoke Detector with built-in relay utilizes a photoelectric sensing method and is designed for use in commercial and residential applications. The device requires hard-wired 120VAC 60Hz power. The detector features two sets of dry alarm contacts: one form-A SPST and one form-C SPDT. The detector has tandem interconnect capability allowing up to 6 devices to be connected together. A 90dBA audible horn is included. The detector can be used with all Sensaphone models.
Smoke Detector 110VAC with Battery backup
Product # FGD-0049-B
The Smoke Detector with built-in relay utilizes a photoelectric sensing method and is designed for use in commercial and residential applications. The device requires hard-wired 120VAC 60Hz power, but also includes internal battery backup. The detector features two sets of dry alarm contacts: one form-A SPST and one form-C SPDT. The detector has tandem interconnect capability allowing up to 6 devices to be connected together. A 90dBA audible horn is included. The detector can be used with all Sensaphone models.
PowerOut Alert Model PS-110
Product # FGD-0054
A compact power outage monitoring device to detect power failures. Easily plugs into any 110 VAC receptacle outlet for operation. Comes with 15 feet of wire.
Zone Water Detector
Product # FGD-0056
The Sensaphone zone water detector is for detecting the presence of water on a floor or in a FALSE ceiling. It comes with 10′ of WaterRope capable of covering a larger area than the FGD-0013 water sensor. Up to ten WaterRopes can be cascaded from a single sensor for even greater coverage. Works with all Sensaphone products and operates on two AA batteries (installed).
Extra 10′ Water Detection Rope
Product # FGD-0063
Extends the water detection rope on the FGD-0056 sensor by an additional 10 feet.
Remote Temperature Sensor 2.8K
Product # FGD-0100
The 2.8K Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured, however this model is recommended to be located in clean, dry environment. For outdoor use model FGD-0101 is recommended.
2.8K Weatherproof Temperature Sensor
Product # FGD-0101
The 2.8K Weatherproof Remote Temperature sensor enables monitoring temperatures at a location away from a Sensaphone unit. It will measure and report the exact temperature back to the Sensaphone unit to which it is attached. The Sensaphone can be programmed to trigger an alarm when conditions exceed the set high or low temperature limits. It may be mounted anywhere air temperatures need to be measured and is suitable for use in wet, dirty environments. This is a highly recommended sensor for every cold storage application above -20°F. For colder temperatures we recommend using sensor part number FGD-0101-TEF. NIST temperature certification is available.
2.8K Temperature Sensor with Glass Bead Vial
Product # FGD-0107
The FGD-0107 is ideal for cold storage temperature monitoring. The glass bead filled vial will buffer any momentary fluctuations that may cause a preliminary alarm dial out, such as defrost cycles, opening of doors, and fans circulating air. The glass beads will slow the response time of the sensor allowing normal daily operations to occur without having an alarm initiated. This is a highly recommended sensor for every cold storage application above -20°F. For colder temperatures we recommended using sensor part number FGD-0107-TEF.
Product # FGD-0222
The FGD-0222 float switch is a plastic side mounted float switch that is cost effective for level control applications in small tanks where it is more convenient to install a level switch through the sidewall of the tank. This style float switch can be rotated for Normally Open or Normally Closed operation. Combine two switches at different levels for high and low level or pump control or alarming.
|Name:||Sensaphone Model 400 Basic Monitoring|
Flexible inputs that support:
Normally Open or Normally Closed contacts
Temperature sensors: -20°F to 150°F
Four channels in the Model 400
Eight channels in the Model 800
|Automatic input type configuration.|
|Programmable recognition times.|
|Alarm Notification:||Four phone numbers in the Model 400.|
|Eight phone numbers in the Model 800.|
|Makes voice phone calls with customized messages for easy identification.|
|Built-in alarm test function to simulate and test the notification process.|
|Includes telephone Line Seizure.|
|Voice Messages:||Built in vocabulary for keypad programming and sensor readings.|
|Record custom voice phrases in your own voice to describe each input zone.|
|Record site identification message.|
|Microphone:||Internal microphone for custom voice message recording.|
|Monitor high sound alarms.|
|Microphone can also be used for remote listen-in feature.|
|Output Relay:||Low voltage NO/NC output relay included.|
|Manual or automatic alarm response switching.|
|Remote Access:||Call in with any Touch-Tone phone to check the status of all monitored conditions.|
|Make programming changes remotely from any Touch-Tone phone.|
|Remotely control the output relay.|
|Local Access:||Keypad and speaker for local programming.|
|Easy voice-prompted programming.|
|Password-protected to restrict programming access.|
|Compatibility:||The Sensaphone 400 is a direct replacement for the model 1104 and CottageSitter.|
|The Sensaphone 800 is a direct replacement for the model 1108.|
|Power Supply:||Comes with plug-in power supply.|
|24 Hour battery backup using 6 size C alkaline batteries (not included).|
|Automatically monitors for power failure alarms.|
|International power options available.|
|Built in CottageSitter Control:||The built in relay can be used to remotely change the temperature of a dual setback thermostat. Provide your own, or order the FGD-0064 Thermostat from Sensaphone.|
|Size:||7½″ W, 2″ H, 8½″ D|
|Shipping Weight:||4 lbs|
|Batteries:||(6) 1.5 Volt "C" cell alkaline (not included)|
|Telephone Connection:||FCC approved RJ-11 plug-in modular connector with 6′ cord|
|Operating Temp. Range:||Unit should be kept between 32° F and 120° F|
|Temperature Sensing Range:||-20° F to 150° F with remote temperature sensor|
|NRTL listed for compliance with U.L. Standard 60950-1|
|Sensaphone 400 Manual (pdf)|
|Sensaphone 400 Sales Literature (pdf)|